Material Safety Data Sheet - Paint
| MATERIAL SAFETY DATA SHEET NPCA 1-84 | |||
| FOR COATINGS, RESINS, AND RELATED MATERIALS REPLACES NPCA 1-82 | |||
| MANUFACTURER'S NAME | EMERGENCY TELEPHONE NO: | ||
| ACRO PRODUCTS, INC. | (713) 703-8351 | ||
| P.O. BOX 506 | |||
| DATE OF PREPARATION: | INFORMATION TELEPHONE NO | ||
| August 28,1996 | (713) 452-5040 | ||
| SECTION 1 - PRODUCT INFORMATION | |||
| PRODUCT NUMBER: ACRO® 7709 | PRODUCT NAME: | ||
| PRODUCT CLASS: | |||
| SECTION II - HAZARDOUS INGREDIENTS | |||||
| Percent | VAPOR PRESSURE | ||||
| Chemical Name | CAS Number | By Volume | TLV | PEL | mmHG @ 20°C |
| Ammonia | 7664-41-7 | 0.7 | 25 PPM | 50 PPM | >760 |
| Dipropyhlene | 29911-28-2 | 10.0 | |||
| Glycol N-Butyl Ether | |||||
| Acrylic Resin | Unlimited | ||||
| SECTION III - PHYSICAL DATA | |||||
| Boiling Range: 212°F | Vapor Density: Lighter than air | ||||
| Evaporation Rate: Slower than ether | Volatile By Volume: 75% | ||||
| Weight Per Gallon: 8.60# | |||||
| SECTION IV - FIRE AND EXPLOSION HAZARD DATA | |||||
| FLAMMABILITY CLASSIFICATION: | OSHA NON-COMBUSTIBLE LIQUID | ||||
| Evaporation Rate: Slower than ether | D.O.T:.NOT REGULATED | ||||
| FLASH POINT: Over 200°F | LOWER EXPLOSIVE LIMIT: 1.1 | ||||
| EXTINGUISHING MEDIA: | CO² | DRY CHEMICAL WATER FOG FOAM | |||
| UNUSUAL FIRE AND EXPLOSION HAZARDS: Keep containers tightly closed. This material will not support combustion unless the water has evaporated. | |||||
| SPECIAL FIRE FIGHTING PROCEDURES: Wear full fire fighting protective clothing, including self-contained. breathing apparatus. Water spray may be ineffective. If water is used, fog nozzles are preferable. Water may be used to cool unruptured containers to prevent pressure buildup. | |||||
| HAZARDOUS DECOMPOSITION PRODUCTS: Normal combustion products include carbon monoxide, carbon dioxide, oxides of nitrogen. | |||||
| SECTION V - HEALTH HAZARD DATA | |||||
| EFFECTS OF OVEREXPOSURE: Eye Contact: May cause irritation. Skin Contact: May cause irritation. Ingestion: May be harmful if swallowed. Inhalation: May cause irritation of throat & lungs. |
|||||
| MEDICAL CONDITIONS PRONE TO AGGRAVATION BY EXPOSURE: None known. | |||||
| PRIMARY ROUTE(S) OF ENTRY: Dermal (Skin Contact) - Inhalation - Ingestion | |||||
| EMERGENCY AND FIRST AID PROCEDURES | |||||
| SPLASH - EYES - Flush eyes immediately with large amounts of water for at least 15 minutes holding eyelids open while flushing. - GET PROMPT MEDICAL ATTENTION. | |||||
| SPLASH - SKIN - Wash affected skin areas with soap and water. Remove contaminated clothing. Get Medical attention if irritation persists. | |||||
| INHALATION - Move person to fresh air. Restore breathing if stopped. If breathing is difficult, give oxygen. Treat symptomatically. Get prompt medical attention. | |||||
| INGESTION - If swallowed, drink one or two glasses of water to dilute - DO NOT INDUCE VOMITING. Call a physician or poison control center immediately for further instructions. Never give anything by mouth to an unconscious person. | |||||
| TOXICITY: Ammonia - Toxic by ingestion. LD 50, Oral-rat: 350 mg/kg. LCLo, Inhalation-rat: 2000 PPM/4H. Although the concentration in this product is low, the high vapor pressure of ammonia makes it possible to exceed the TLV of PEL in drum head space or other confined areas. The liberation of ammonia may be retarded because of chemical neutralization in the product. | |||||
| SECTION VI - REACTIVITY DATA | |||||
| STABILITY: Unstable X Stable Hazardous Polymerization will X will not occur under normal conditions | |||||
| CONDITIONS TO AVOID: None Known | |||||
| INCOMPATIBILITY (MATERIALS TO AVOID): Strong oxidizers, amines, acids, hydroxyl or other reactive hydrogen compounds, strong oxidants, caustics. | |||||
| SECTION VII - SPILL OR LEAK PROCEDURES | |||||
| STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED: Keep personnel a safe distance away from the spill area. Avoid breathing vapors. Contain and remove with inert absorbent material and non-sparking tools. Minimize contact. Before attempting cleanup, refer to Hazard Caution information in other sections of this MSDS form. | |||||
| SECTION VIII - SAFE HANDLING AND USE INFORMATION | |||||
| HANDLING: Keep closure tight and container upright to prevent leakage. Avoid skin and eye contact. Wash thoroughly after handling. Avoid breathing of vapor or spray mists. Do not handle until all safety precautions have been read and understood. Empty containers should not be re-used. Avoid using pressurizable equipment which has aluminum or zinc parts. Use with adequate ventilation. Because empty containers may retain product residue and vapors. Do not cut, puncture or weld on or near the empty container. Do not smoke where this product is used or stored. | |||||
| STORAGE: Store only in well-ventilated areas. Do not puncture, drag, or slide container. Keep container closed when not in use. | |||||
| VENTILATION: Sufficient ventilation in pattern and volume should be provided to keep the air contaminant concentration below applicable exposure limits. Heavy solvent vapors should be removed from the lower levels of work areas, and all ignition sources (non-explosion proof equipment) should be eliminated if flammable/air mixtures will be encountered. All application areas should be ventilated in accordance with OSHA regulation 29 CFR Part 1910.94. Use ventilation to remove airborne decomposition products formed during welding or flame-cutting of surfaces coated with this product. Caution: Solvent vapors are heavier than air and collect in lower levels of the work area. | |||||
| SKIN PROTECTION: Use neoprene or rubber gloves to prevent skin contact. | |||||
| EYE PROTECTION: Use safety eyewear including safety glasses with side shields and chemical goggles as minimum protection. | |||||
| OTHER PROTECTIVE EQUIPMENT: Use disposable or impervious clothing if work clothing contamination is likely. Remove and wash contaminated clothing before reuse. Use protective cream if skin contact is likely. | |||||
| HYGIENIC PRACTICES: Wash hands before eating, smoking or using toilet facility. Do not smoke in any chemical handling or storage area. Food or beverages should not be consumed anywhere this product is handled or stored. Wash thoroughly after handling. | |||||
| SECTION IV - DISPOSAL CONSIDERATIONS | |||||
| DISPOSAL METHOD: Disposal should be done in accordance with Federal (40CFR Part 261), state and local environmental control regulations. If waste is determined to be hazardous, use licensed hazardous waste transporter and disposal facility. | |||||
| SECTION X - TRANSPORTATION INFORMATION | |||||
| DOT PROPER SHIPPING NAME: | PAINT | DOT HAZARD CLASS: N/A | |||
| DOT UN/NA NUMBER: | N/A | PACKING GROUP: N/A | |||
| SECTION XI - SPECIAL PRECAUTIONS | |||||
| Avoid breathing sanding dust. Can cause allergic respiratory reaction. Can cause allergic skin reaction. Prevent prolonged or repeated breathing of vapor or spray mists. Do not weld or flame-cut an empty drum or container. Do not handle until the manufacturer's safety precautions have been read and understood. | |||||